Carbon Trading

The Kyoto Protocol,1992 in the UN Framework Conventions on Climate Change but adopted in 1997 established the basis of Carbon Trading, Carbon offsets.
192 nation agreed to reduce Carbon emissions, which Identifies the 6 GHG gasses as 1) CO2 2) methane, 3) N2O 4) hydrofluorocarbon  5) perfluorocarbon and 6) sulphur hex-fluorocarbon. All these gases are referred to as Carbon emission, Carbon dioxide is the weaker global warming effect but the amount of it is the largest amount. Before the Kyoto Convention 2 Convention were held to establish the basis of Carbon emission, what is was considered as Carbon emission etc.

Carbon Trading Price Fluctuations

carbon-trading graph

carbon-trading in Asia

Protocols

The Carbon Trading has been defined in 3 conventions as follows:
a) Earth Summit-Conference on Environment and Development –UNCED, Rio 1992
b) United Nation Framework Conference on Climate Change UNFCCC( not binding due to no time limit was set by the UN
c) Kyoto Protocol, 1997
Carbon Trading is under the purview of the UN, Article 26 of the Vienna Convention on the Law of Treaties 1969 and therefore the Kyoto Protocol is a treaty
In Malaysia, the Ministry of Natural Resources and Trade is in charge of CDM. In Malaysia, 100 tonnes were traded in 2008, at RM4.8 Billion. I ton of carbon was  sold at RM48. The price of carbon rallied from US 25 – US 12 over these years.

Ways to earn Carbon Credits for Carbon Trading

There are a few established legitimate ways of Carbon trading , which are:
a) using PV solar panels as Carbon Offsets are made
b) using wind turbines as Carbon Offsets are made
c) designing Net Zero Carbon Emission buildings or Net Zero Energy Buildings
d) Managing a forest ( Tropical) or wetlands, as the soil and tree sequesters CO2 by using PV solar panels as Carbon Offsets is made
e) Investing in a Carbon reducing projects such as Renewable energy projects, Geo-Thermal, Biomass, PV solar panels, micro turbine and wind turbines.
How much can you gain by Carbon Trading?
A typical building as in a 100,000 sq ft of gross built commercial space up area can offset carbon 390 tons of carbon per year.
The financial amount you can trade is 390 ton per year xRM48/ton=RM18,720
Carbon Emission for Combustion Fuels
Coal…………………0,37kgCO2/kWh
Gasoline…………. 0.27kg CO2/kWh
Diesel………………0.24kgCO2/kWh
Light Oil…………. 0.26kgCO2/kWh
Natural Gas………0.23kgCO2/kWh
LPG…………………0.24kgCO2/kWh
Malaysian CO2 Emission Coefficient Rate is 0.631 kgCO2/kWh

Check out our Architect,Green Architect, House Plan relating to Net Zero Carbon designs

Carbon Trading

Green architect

Prepared by Ar Perumal Nagapushnam
Net Zero Emission Building Architect

Certifying Bodies for Net Zero Energy Buildings

The certifying bodies for Net Zero Energy Buildings in the US A are :
A) Department of Energy
, DOE, an equivalent to the Malaysian Ministry of Energy
B) Zero Energy Commercial Building consortium
C) New Building Institute. NBI
A nonprofit organization that provides research and improved energy performance in commercial buildings
D)International Living Future Institute

The Programs surrounding the Net Zero Energy Buildings are :
1)2030 Challenge
The top 80% of 10 Architectural firms and 70% of the top 20 Architectural firms use The Challenge 2030.whereby all developments, new buildings and major renovation shall be carbon neutral by 2030 in the US and thereby reducing the temperature by 2 degree below the pre-industrial times.Net Zero Energy Buildings are also refereed too as Zero Energy Buildings.

2)Ashrae Vision 2020
Ashrae is a strong supporter of NZEB, and where Ashrae Vision 2020 was developed to promote energy Efficiency. NZE is defined as uses as much energy as it produces as measured at the site.

The Industry Codes and Regulations  surrounding the Net Zero Energy Buildings  in the world are: 
1)Security Act of 2007
2)Energy Independence and Security Act( Malaysian Renewable Energy Act)
3)California Public Utilities Commission
4)Massachusetts Zero Energy Building Task Force

5)European Union
The parliament passed a directive to achieve NZE by 2019 but focused on residential buildings and not commercial buildings: UK-Zero Carbon Hub to be carbon neutral by 2016, Germany-Passivhaus, Netherlands-energy neutral by 2020, France to be Energy positive by 2020.

The Building Codes surrounding the Net Zero Energy Buildings  in the USA are:  
1)IgCC– International Green Construction Code
This code is developed in conjunction with AIA,USGBC (MGBC-a Malaysian equivalent body –Malaysian Green Building Council) , 2)ASHRAE,ASTM,IES
3)CalGreen, California Green Building
4)Standard 189.1

The Building rating and Energy Labelling Systems surrounding the Net Zero Energy Buildings  in the USA are:

1) Energy Star
Is an energy labelling program of EPA( Environmental Protection Agency) and DOE( Department of Energy) It labels energy efficient products, homes, and commercial buildings. It scores on a table of 1 to 100.100 is a top performer. Energy Star does not recognize NZEBs. But the NZEB would score 90 in this program.
2) Leed/Green Building Index
The energy efficiency is the first and primary focus of the certification, one cannot obtain a platinum certification without designing for a high performance building. Incidentally the Net Zero building would easily obtain the Platinum with a marginal additional cost
3) Living Building Challenge by International Living Future Institute
Defines Imperatives for Net Zero Energy:

  • Net Zero Energy-if this imperative is not achieved it will not be qualified for the Living Building Challenge. The definition of NZEB are on: renewable energy, photo voltaic, wind turbines, water powered micro turbines, direct geo thermal. Biomass or combustion of any kind is not allowed. Hydrogen cell is allowed if energy is fueled by Hydrogen. Off grid connection is a must.
  • Site Imperatives-Site is restricted for gray fields and brownfields
  • Equity Imperatives-fresh air, sunlight and natural waterways
  • Beauty Imperatives-Beauty, spirit, inspiration and education

 

Hyper Green architect

Green architect Net Zero Energy Buildings Architect

 

 

 

check out our Green and Sustainable House Floor Plans, click here
c
heck out our Architect, Green Architect, House Plan

 

Prepared by Ar. Perumal Nagapushnam

Net Zero Carbon Seminar and Net Zero Energy Seminar

Book NOW click here- Net Zero Carbon Seminar

Net Zero Energy Seminar

Net Zero Energy and Carbon Seminar

This is a  synopsis of the all the 14 talks In our  Net Zero Carbon Seminar .

Book NOW click here- Net Zero Carbon Seminar

 

We have organized this Net Zero Carbon Seminar with the intention to promote the idea in simplicity for all to understand. This will spear head the designs of buildings as Energy Efficient . Design of building will be a response to the call of global weather changes. This seminar is also some time refereed to as Architect Seminar,Architect training,Architect workshop,Engineering workshop,Engineering seminar, Engineering Training,Architect Conference, Engineering Conference, International Architect Conference or International Engineering Conference.

Talk 1. Targeting for  Net Zero Carbon Emission in Process and Product Design …Net Zero Energy Buildings
Synopsis of the Talk  Dr YewAi Tan

Oder a seat for the seminar now, by clicking here  Net Zero Carbon Seminar

At the UN Climate Summit in New York on 23 September 2014, the Prime Minister of Malaysia reiterated Malaysia's commitment towards reducing its carbon emissions, in terms of emissions intensity of its Gross Domestic Product (GDP), by 40% by 2020. This will be implemented by reducing carbon emissions through new policies on climate change and green technology. Under the 11 th Malaysian Plan, RM 2.3 billion has been set aside for green technology based projects. This pledge, originally made at the United Nations Climate Change Conference (UNFCC) 2009 in Copenhagen, Denmark, was conditional to receiving technological and financial assistance from developed countries. This year, Malaysia looks on track to hit the targeted carbon reduction emissions having achieved 33% reduction carbon intensity of its GDP. As GDP is the monetary value of finished goods and services, Malaysia will therefore have to grow its GDP without a parallel increase in emissions in order to achieve the 40% reduction.

The Climate Change problem will never go away on its own and ignorance on its seriousness is no longer an excuse for inaction. For effective mitigation

Net Zero Carbon and Net Zero Energy Cost

Net Zero Energy Cost Seminar

against climate change, there must first be acknowledgement that the burden must be borne by all. The next step will be how each and every one of us, the residents of planet earth, can help in reducing carbon emissions with a target towards achieving zero net carbon emissions. Before embarking on efforts to achieve zero carbon emission in process and product design, it is essential to be clear and familiar with the many terms and terminologies commonly associated with carbon emissions such as greenhouse gas (GHG) emissions, carbon footprint (CFP) , carbon capture, carbon sink, carbon neutral and energy neutral, etc. For example, CFP is defined as a measure of GHG emissions over the full life cycle of a process or product including the design stage, if applicable. It is the overall amount of not only carbon dioxide (CO 2 ) emissions but also emissions of other GHG such as methane (CH 4 ), nitrous oxide (N 2 O),chlorofluorocarbons (CFCs), hydro fluorocatbons (HCFs) and sulphur hexafluoride (SF 6 ) that are directly and indirectly associated with a product along its supply chain. GHG emission is an integral part of all systems of production and consumption, In the case of a process or product design, each activity within a supply chain process step which is involved in the production or design of the product must be analyzed to determine CFP measured in mass units (kg, t) of carbon dioxide equivalent (CO 2 eq) emitted. Through a carbon audit, any sector of an industry (e.g. palm oil or building industry) can systematically address environment-sensitive practices along the whole chain in the design and process of a product. One of the most important move that can be taken is to ensure that all products and services made and provided involve minimal carbon emissions. To arrive at net zero carbon emissions, emissions must be offset or subtracted and ways to achieve carbon neutrality will be highlighted in the paper. Suggestions on the formulation of possible mitigation strategies to curb GHG emissions and ways to target for zero net carbon emission by balancing emissions with simple negative emissions solutions such as tree- planting and the use of other more advanced technologies including the use of renewable energy generated from waste products, the sun or wind will also be discussed. The goal is to provide required information on the importance of our shared responsibility to reduce carbon emissions in the hope of ending the high emitting and energy-hungry practices of the modern world.

Talk 2. ACMV system design for Net Zero Energy Buildings in the tropics in the  Net Zero Carbon Seminar

by Dr Stellios Plainiotis

Net-zero energy buildings (Net-ZEBs) are a quantifiable design concept and an absolute solution to minimize the operational environmental impact of buildings. However designing such advanced buildings presents a challenge because there is no established design strategy to methodically reach the goal and many of the available calculation tools have limited applicability for Net-ZEBs. Appropriate modelling of building-integrated energy systems (passive and active) is essential for the design of ACMV systems and the study of optimal control strategies. These systems will play a major role in achieving the net-zero energy goal and need to be carefully selected, modelled, and sized for an optimum design. This talk focuses on optimizing active ACMV systems with emphasis on building simulation and parametric analysis. This presentation will review current design practice and tools for designing ACMV systems and presents methods employed by NEAPOLI to design ACMV systems in the tropics. It also discusses modelling issues and outlines the procedure used in several optimization case studies by NEAPOLI.

Talk 3: Achieving Net Zero Energy Status: the case of the Hospitality Sector in SE Asia

Synopsis of the Talk  in the  Net Zero Carbon Seminar by Dr Stellios Plainiotis
Oder a seat for the seminar now, by clicking here  Net Zero Carbon Seminar

Although the hospitality industry is responsible for only 2% of the world’s CO2 emissions, it makes an excellent sector for achieving Net-Zero Energy status  because energy  consumption  is  higher  than  in typical residential and non-residential buildings, so  there  is  a  larger potential for energy saving measures. Hospitality projects in Asia can benefit from reaching net-zero status through:

  • Energy savings and reduction of operational costs
  • Unique positioning in a highly competitive market
  • Improved image and service for guests
  • Access to a new “sustainability” market segment, both individuals and companies
  • Increased comfort as an added-value for hotels’ guests
  • Corporate Social Responsibility targets met; Environmental, social and economic sustainability.

There are however great challenges related to financing the additional initial capital expenditure and to  business model that includes a number of energy intensive operations associated to their customers’ comfort and expectations, therefore closely linked with their competitiveness and viability.  After presenting the fundamental concepts, design strategies, and technologies required to achieve net-zero energy in hospitality buildings, this presentation will discuss a case study of a Net-ZEB Hotel in Malaysia by NEAPOLI.

Talk 4: Generative and parametric design optimization techniques towards Net Zero Energy Buildings, Synopsis of the Talk  Net Zero Carbon Seminar by Mr Theodre G

Oder a seat for the seminar now, by clicking here  Net Zero Carbon Seminar

Net Zero Energy Buildings (Net-ZEBs) represent a new paradigm that radically changes the way we view and construct buildings. Our current practices, tools, and culture involved in the design and development of contemporary buildings are not entirely compatible with this new perspective. We are in dire need of new design paradigms that will allow the re-conception of the design process itself. NEAPOLI’s Research & Development efforts are focusing on two of the most important innovative design methodologies available today: generative and parametric design.

Generative design can be defined as an evolutionary process that charts the development of an original idea, searching quickly through all its possible permutations, testing different design configurations, learning and improving at each step. New design tools employed at NEAPOLI now allow cycling through thousands of design alternatives in small amounts of time, making generative design a very powerful approach especially for the early stage of design.

Parametric design can be defined as the varying of one (or more) building parameter(s) and performing a simulation to quantify that parameter’s impact. NEAPOLI employs parametric analyses to provide at least three valuable pieces of information:

  1. The optimal/near-optimal value of a design parameter, always in relation to other often competing parameters. If the performance metric for a particular parameter indicates that there is an optimum value, the design team may wish to use this value in the design, assuming it is practical, economical, and compatible with other design aspects.
  2. The relative sensitivity of a parameter. This is particularly useful when multiple parameters are compared.
  3.  The relative importance of accurately modelling a building system. The most care in accurate modelling should be given to the aspects that are most sensitive. Sensitivity analysis is a very important confidence building tool for NEAPOLI consultants.

This presentation will provide an exploration of these innovative design approaches, it will show how they can provide competitive advantages over contemporary processes, and finally share ideas and examples of their implementation in the design of Net-ZEBs.

 Talk 5: Net Zero Energy Design in practice: design optimization methodologies and tools Synopsis of the Talk  in  Net Zero Carbon Seminar  by Mr Theodre G

Traditional construction practice created buildings to meet current needs, without addressing how well they fit with the natural environment. Because they were lacking adaptive capabilities, they would usually require remodeling or replacement when use-patterns or external conditions changed, an approach that is costly both financially and environmentally. Net-ZEB buildings can provide solutions to this because not only are designed and built to produce all of their own energy, capture and treat all water, but they can also designed and operated to have a net-positive impact on the environment, including repairing surrounding ecosystems.

However new and innovative tools are required to achieve and realise that vision. While generative and parametric methodologies are gaining ground in both architecture and design practices, their practical use remains limited due to the lack of design tools equipped with generative and parametric capabilities.

This presentation will describe the current status of generative and parametric tools for the building design industry and how these are being used to improve building design. In a workshop-like manner, the audience will be taken, step-by-step, through real-life design examples showcasing NEAPOLI’s ‘box of tools’ paradigm which allows the development of highly complex and integrated models able to assess in parallel a wide variety of building performance and design issues.

Talk 6 : Net Zero Energy Design in Building Passive Design, Design Overall Integrated Design Approach in Net Zero Energy Design –Synopsis of the Talk in  Net Zero Carbon Seminar
by Ar Perumal Nagapushnam

  1. What is Net Zero Energy?
  2. Definitions of Net Zero Energy as per NREL

Net Zero Energy-The NREL has defined four ways of measuring the Net Zero Energy in buildings: –Net Zero Site Energy, Net Zero Source Energy, Net Zero Energy Emissions  , Net Zero Energy Cost

  • Principles of Net Zero Energy in establishing Net Zero Energy buildings
  • The overall integrated design approach with the Energy affecting considerations from the outset to create High Energy Performance building or Energy Efficient buildings.
  • Building Design Principles are:
    1) Optimum Orientation,
    2) Super Insulation of buildings by good thermal resistance materials,
    3) Shading, smart landscaping, living roof etc
    4) Good BAS system to manage energy consumption
    5) LED high performance systems
    6) Good active Mechanical and Electrical system
    7) Renewable Energy ( 4 Net Zero Energy categories)
    8) Energy Management in place-Sub metering, energy audit and Maintenance team crew
  • Calculations for NZEBs.
  • Conclusion with some real life project case studies of buildings designed in Malaysia
  • Terms used in NZEB
    NREL ,National Renewable Energy Laboratory of the USA, renewable energy and energy efficiency technologies. Energy Neutral Zero Carbon Hub Renewable Energy, Low Energy Building, High Performance Building ,ENERGY STAR ,Energy Protection Agency ,Building Code

Talk 7: Net Zero Emission Definitions and terms Calculations

Synopsis of the Talk in  Net Zero Carbon Seminar By Ar Perumal
Oder a seat for the seminar now, by clicking here  Net Zero Carbon Seminar
  1. What is Net Zero Carbon Emission?
  2. Terms used in of Net Zero Emission such as Carbon Neutral, Carbon footprint, ecological footprint, Water footprint, Biofuel- Primary energy Global warming, Acidification, Eutrophication, Carbon footprint, Ecological footprint, Accounting ,Carbon credit, Carbon offset , Carbon Emission, Transportation Carbon ,Operational Carbon-,Embodied Carbon emissions, Carbon neutrality, Life Cycle Assessment (LCA) , Life Cycle Cost (LCC),Water footprint, Water neutrality, ‘Water neutral’ ,Bluewater ,Green water, Grey waterEnergy audit, Fossil fuel,Green energy
  3. Accounting Principles of Net Zero Emission
  4. Comparison of Net Zero Emission as defined by Challenge 2030, NREL and Zero Carbon Hub.
  5. Benefits of Net Zero Emission in design with Biodiversity in designs.
  6. Conclusions with the importance of Net Zero Emission

Talk 8:Renewable Energy – and the case for Zero Carbon

Synopsis of the Talk in  Net Zero Carbon Seminar
Oder a seat for the seminar now, by clicking here  
Net Zero Carbon Seminar

By: Gregers Reimann

In a Low Carbon World, we will have to deploy on the dual strategy of energy efficiency and renewable energy. In this presentation, the focus will be on renewable energy and its stronger and stronger case as opposed to fossil fuels. Interestingly, renewable energy costs are starting to achieve grid parity. Moreover, once the true cost of fossil fuels is factored in, namely the external costs like (carbon) pollution, the business case for renewable energy becomes even better.

For Malaysia, biomass and solar energy are the most applicable conventional renewable energy sources, but once implemented on a big scale, they both take up significant land area. Therefore, apart from re-stating the importance of energy efficiency, this presentation will also examine how renewable energy can be integrated in our built environment without taking up ‘extra space’.
Highlights of this presentation include:

Referencing the recent IMF study on the true cost of fossil fuels and its astounding conclusions. For Malaysia, for example, if we were to pay the real cost of fossil fuels, the petrol should cost RM4.50 per liter, which is more than double of the current cost.

Calculations example of how much solar photo-voltaic panels are needed to cover the entire Malaysian annual electric consumption. The result may surprise you in a positive way.

Examples of BIPV (building integrated photovoltaic) and other innovative to integrate renewable energy in the built environment

Talk 9 : “Zero Energy / Carbon and Innovative Tropical Building Case Studies

Synopsis of the Talk in  Net Zero Carbon Seminar By: Gregers Reimann
Oder a seat for the seminar now, by clicking here  Net Zero Carbon Seminar

The biggest and cheapest carbon emission savings are found in the building sector. Therefore, the building sector will play a key role in achieving the low carbon sustainable society that experts are urgently calling for. This presentation will focus on Malaysian case studies of low energy buildings both for commercial and residential sector. The focus will be on the design strategies employed in the case studies, both with respect to innovative passive building design by working with the climate and with respect to innovative active design solutions for ventilation, cooling, lighting and controls.  The low carbon aspect of the presentation will focus on the operational energy, which constitutes the bulk of the life-time carbon emissions for most buildings. The case studies presented have achieved measured energy savings of 50% or more and often with an attractive short payback time from reduced monthly energy bills.
The presentation will also re-examine how to approach thermal comfort for people in an energy efficient way and with the added benefit of providing improved air quality.

Some of the case study highlights include:

Case study no. 1: Zero energy bungalow (2016) in Kuala Lumpur with innovative natural cooling system that lowers the indoor temperature by 2-3°C, hence, eliminating the need to use air-conditioning. In fact, the bungalow does not have any air-conditioning installed.

Case study no. 2: Innovative high rise day-lighting system (2015) in Kuala Lumpur. Even though the occupants engage the manual facade window blinds, the daylight system maintains 7-meter perimeter zone of the office fully day-light.

Case study no. 3: Energy efficient building retrofit project (ongoing) saving 50% of the energy consumption in part by a new approach to providing thermal comfort to the building occupants

Case study no. 4: Innovative energy efficient and low energy slab cooling as exemplified in two Malaysian offices buildings, the GEO Building (2007) and the ST Diamond building (2010).

Talk 10: Targeting for Zero Net Carbon Emission in Process and Product Design

Synopsis of the Talk in  Net Zero Carbon Seminar
Oder a seat for the seminar now, by clicking here  
Net Zero Carbon Seminar

  by YewAi Tan

At the UN Climate Summit in New York on 23 September 2014, the Prime Minister of Malaysia reiterated Malaysia’s commitment towards reducing its carbon emissions, in terms of emissions intensity of its Gross Domestic Product (GDP), by 40% by 2020. This will be implemented by reducing carbon emissions through new policies on climate change and green technology. Under the 11th Malaysian Plan, RM 2.3 billion has been set aside for green technology based projects.  This pledge, originally made at the United Nations Climate Change Conference (UNFCC) 2009 in Copenhagen, Denmark, was conditional to receiving technological and financial assistance from developed countries. This year, Malaysia looks on track to hit the targeted carbon reduction emissions having achieved 33% reduction carbon intensity of its GDP.  As GDP is the monetary value of finished goods and services, Malaysia will therefore have to grow its GDP without a parallel increase in emissions in order to achieve the 40% reduction.

The Climate Change problem will never go away on its own and ignorance on its seriousness is no longer an excuse for inaction.   For effective mitigations against climate change, there must first be acknowledgement that the burden must be borne by all.  The next step will be how each and every one of us, the residents of planet earth, can help in reducing carbon emissions with a target towards achieving zero net carbon emissions.

Before embarking on efforts to achieve zero carbon emission in process and product design, it is essential to be clear and familiar with the many terms and terminologies commonly associated with carbon emissions such as greenhouse gas (GHG) emissions, carbon footprint (CFP) , carbon capture, carbon sink, carbon neutral and energy neutral, etc. For example, CFP is defined as a measure of GHG emissions over the full life cycle of a process or product including the design stage, if applicable. It is the overall amount of not only carbon dioxide (CO2) emissions but also emissions of other GHG  such as methane (CH4), nitrous oxide (N2O), chlorofluorcatbons (CFCs), hydrofluorocatbons (HCFs) and sulphur hexafluoride (SF6) that are directly and indirectly associated with a product along its supply chain.

GHG emission is an integral part of all systems of production and consumption, In the case of a process or product design, each activity within a supply chain process step which is involved in the production or design of the product must be analysed to determine CFP measured in mass units (kg, t) of carbon dioxide equivalent (CO2eq) emitted. Through a carbon audit, any sector of an industry (e.g. palm oil or building industry) can systematically address environment-sensitive practices along the whole chain in the design and process of a product.   One of the most important move that can be taken is to ensure that all products and services made and provided involve minimal carbon emissions.  To arrive at net zero carbon emissions, emissions must be offset or subtracted and ways to achieve carbon neutrality will be highlighted in the paper.  Suggestions on the formulation of possible mitigation strategies to curb GHG emissions and ways to  target for zero net carbon emission by balancing emissions with simple negative emissions solutions such as tree-planting and the use of other more  advanced technologies including the use of renewable energy generated from waste products, the sun or wind will also be discussed. The goal is to provide required information on the importance of our shared responsibility to reduce carbon emissions in the hope of ending the high emitting and energy-hungry practices of the modern world.

Talk 11: LCA and LEED for Enhancing Energy and Environmental Performance of Buildings

Synopsis of the Talk in  Net Zero Carbon Seminar by YewAi Tan
Oder a seat for the seminar now, by clicking here  Net Zero Carbon Seminar

The orthodox goal of increasing housing for growing population needs is now slowly being replaced by a shift in focus to buildings that promote variety, access to healthy and clean air, and a healthy and ecological sustainability environment. This is driven by risks that climate change poses for human and natural systems.  Global warming, sea level rises and associated extreme weather events are now adversely affecting population health and will continue for centuries to come.

With over half the world’s population now living in urban areas, resilient urban housing plans will need to incorporate more extensive approaches to meet the challenges of a world imperiled by severe weather conditions resulting in floods and droughts.  Attention will be on enhancement of ecosystem health as well as the health and support of thriving urban environments.  The building and construction industry is known to be the one of largest contributors of environmental pollution.  According to the United Nations Environment Program Report, buildings account for a third of greenhouse gas (GHG) emissions, 25% of global water consumption and 40% of global energy consumption and resources.   The fact that this energy consumption in buildings can be reduced by 30% to 80% using proven and commercially available technologies accentuates the importance of greening buildings as one of the most effective ways to reduce the carbon footprint (CFP) of the building and construction industry.

The main objective of Green buildings is to reduce negative impacts and increase occupants’ health. Green buildings address issues concerning sustainable site planning, water and energy efficiency, conservation of resources and improved health, and the impact of buildings on health and indoor environmental quality.  The Malaysia Green Building Index (GBI), initiated in 2009, is based partly on USA’s Leadership in Energy and Environmental Design (LEED) but adapted to fit the Malaysian climatic conditions.

The LEED rating system is a voluntary U.S. based  green building programme which aims to “evaluate environmental performance from a whole building perspective over a building’s life cycle, providing a definitive standard for what constitutes a green building’’. In essence, the LEED method rates the energy and environmental performance of buildings and is clearly an environmental assessment tool.

CFP is a computed number which an industry can use as a baseline reference for improvement.  At the same time, the methodological tracing through Life Cycle Assessment (LCA) of the various sources of GHG emission in sustainable buildings will give a clearer indication on where mitigation steps can be implemented for GHG reduction.  LCA is also an essential component of building assessment as it is a step-by-step process for evaluating the environmental burdens associated with an activity, product or process.  The method, based on the life cycle of the activity, product or process identifies and quantifies energy and materials used and wastes released to the environment, thereby assesses the impact of those energy and material use and wastes to the environment. LCA is applicable to all system levels in the building sector. Each system has its own set of assumptions and limitations and each is designed to address certain aspects of environmental impacts.  An inventory of all inputs (e.g. energy, material, water used) into and outputs (final product, emissions, wastes)  out of the system will allow for calculation of impacts based on energy consumption, waste generation or other impact categories such as global warming or land use.   The approach can be used for the selection of building materials or for assessing the environmental impact associated with the physical building.  Therefore, in order to obtain useful information from environmental assessment of buildings, the rigor of an LCA approach can be used to support and complement the evaluation of LEED compliance.

Malaysia’s Green Diamond Building headquarters of the Energy Commission (Suruhanjaya Tenaga) of Malaysia in Putrajaya won Southeast Asia Energy Prize in 2012. The building, completed in 2009, earned Platinum ratings under Malaysia’s Green Building Index (GBI) and Singapore’s Green Mark program.

Book NOW click here- Net Zero Carbon Seminar

 

Hyper Green architect

Green architect

 

 

 

 

 

Organized by System Design Architect
Ar Perumal Nagapushnam.

Net Energy Building for Office Tower

Models for Net Zero Energy Buildings are used by  Net Zero Architects to calculate the amount of energy saving in the schematic stages of the design, which then are  used as a basis of energy  design control through out the design implementation stages.The model is a 3-D electronic model of a building, it is also a simplified model without much details of the building, which will help calculate the calculation intentions. It is refereed as a shoe box model. There are many types of models used in designing a Net Zero Energy Building design.There are 11 types of Energy Model, which are:

1.) Heat Transfer model for Net Zero Energy Buildings in House Floor Plans
Model show that show how the heat is transferred from the outside to the interiors of the building architectural floor plans.
2.) Lighting model for Net Zero Energy Buildings  in House Floor Plans
Model showing how the day light penetrates top the interiors of the building and it helps Architect to design the light fittings in the building architectural layout outs.
The study of a the lighting levels through out the day would show the amount of light derived from the sun into the building and it helps the Net Zero Energy Buildings Architects to design the additional lighting need ed to make the building sufficiently lighted up.
The amount of light that can be daylight harvested can also be studied, note the amount of light lux derived from the sun is about 100,000-140,000 lux in comparison to what is needed in the office space is only a merger 400lux, the potentials of day light harvesting has to be considered seriously in the light of the current worldwide needs.
3.) BIM Model-Building Information Model for Net Zero Energy Buildings  in House Floor Plans
A digital computerized model, which has information about clashes of the architectural and engineering elements, it provides information about costing, and when plug-in with time project management time line program, we are able to produce the physical model developing over the time line of the builder. The model can be used to study the thermal heat, energy model and total embodied energy of the building architectural plans. This is a great tool for architects and project management consultants.
4.) Energy Model  for Net Zero Energy Buildings  in House Floor Plans
–A simple model used for computerized computation of the energy usage in the building for every month or per year based on the climate conditions, and the building insulation and orientation for buildings. A designing tool, which is helpful to Net Zero Energy Buildings Architects in  choosing the mass proportion and selection of materials.
5.) Wind Model for Net Zero Energy Buildings  in House Floor Plans
– A simple model used for computerized computation of the direction of the wind into the building based on the openings of the buildings. It will help Net Zero Energy Buildings Architects to decide where openings shall be created to enable wind to be harvested.
6.) CFD-for Net Zero Energy Buildings  in House Floor Plans
Computerized Fluid Dynamics is a study of the flow of air in  a  building, where the direction is established and the comfort is designed and it is a tool for Net Zero Energy Buildings Architects to remove impediments to comfort. It helps the architects to design buildings of how the heated air flows, how the ventilation of air flows throughout the building.
7.) Massing and Study Model for Net Zero Energy Buildings  in House Floor Plans
-a model used by Net Zero Energy Buildings Architects to evaluate the proportion, the shape , bulk , form aesthetics and how the form affects the environment.
8.) Thermal Model for Net Zero Energy Buildings  in House Floor Plans
– a model which reveal the sides of the building, where is heated up during the day. With the Thermal model the building designer may be able to decide how the building may be treated or insulated to keep the thermal heat from entering in to the building.
9.) Solar Path Model– for Net Zero Energy Buildings  in House Floor Plans
The path of the sun through out the year, and how it affects the building’s shadow and how it affects the sun’s rays into the window openings and show how the sun’s ray falls on the building and the building’s shadows is cast and how the neighboring building’s shadow affect the building that is being designed.
10.) Ventilation Model– for Net Zero Energy Buildings  in House Floor Plans
The study of wind and movement of air within the building

Contact us for your NZEB designs..we will be able to help you in the interest to secure the building in being less independent to the energy utility companies.check out our house floor plans.

Prepared by Net Energy Architect Perumal Nagapushnam, Green Architect of http://www.sda-architect.com/